With the recently-acquired Mustang in the garage for the winter of 2003-2004, I set out to do three things in preparation for the 2004 driving season: join the local Mustang club, subscribe to Mustang Monthly magazine, and obtain as many vendor parts catalogs as possible.
The N.J.-based club was the GSRMC (Garden State Region Mustang Club), and soon after joining, its President invited me to submit an article about my car, as we both surmised it was the only GT/CS in the club.
Prior exposure at events like Carlisle had shown that (especially compared to Isetta vendors) there were dozens of Mustang parts suppliers, so any needed part should be only a phone call or mouse click away. I was soon to learn otherwise.
As weather allowed, I would slip into the garage to perform some preventative maintenance: tune-up, oil change, coolant hoses & clamps, etc. Removing the air cleaner lead to the discovery, missed by me and unmentioned by previous owner Tony, that the heater hoses were disconnected from the heater core at the firewall. Against my better judgment, I reconnected them, filled the system, started it up, and ran the heater. All was dry, so I let it be.
As I placed orders for my Mustang-specific parts, I sampled various vendors, including Mustangs Unlimited, CJ Pony Parts, Virginia Classic Mustang, and NPD. Two truths became apparent: first, the quality of aftermarket parts varied widely, and was not always good, to the point that substandard parts were returned; and second, the idea that any part could be found at any vendor was hindered by my engine.
The “X code” 390 2-barrel FE-block was so rare that most Mustang suppliers did not carry parts for it. (Some catalogs, and some otherwise-well-written tomes on the Mustang did not even acknowledge that Ford used this engine in Mustangs!) Out of 317,000 1968 Mustangs, the X-code engine was put into 476 of them (2/10ths of 1%). Among California Specials, 75, or about 2%, used it. Either way, that makes for one rare engine.
The vast majority of its parts are shared with the S-code 390 “GT” 4-barrel engine. The differences are all on top: intake manifold, carb, air cleaner, emission controls, and various connecting parts. For my needs, I was stymied at obtaining vacuum hose connection parts, and a replacement for the missing air cleaner snorkel. (Much later, I found that the snorkel was not being reproduced, and was available used for about $900. I didn’t buy it.)
Early in 2004, the Mustang Club of America (MCA) announced that it would be hosting a 40th anniversary celebration for the Mustang in April, with the event to be held at Nashville Speedway in Tennessee. (The Ford Mustang debuted at the New York World’s Fair in April 1964.) Checking with the GSRMC, there seemed to be lukewarm interest in attending. However, the New England Mustang Club was organizing a caravan, stopping at various points to pick up participants, and they would be stopping at CJ Pony Parts in Harrisburg PA. My wife was willing, so we signed up.
On a rainy April day, we headed out to Harrisburg. The group, at this point about a dozen strong, showed up a short time later. The New England crowd was friendly, and warmly welcomed us. (They promised a “wicked good” journey.) It was nice to have some company on the trip south. The Mustangs consisted primarily of first-generation cars and Fox bodies. Most were driven; several were trailered. As we traveled, other Mustangs joined, and soon there were close to 20 cars. The group was informed that our destination for the night was Harrisonburg VA, and that we would be in Nashville by the afternoon of the second day. The weather remained cool and damp, but we were comforted by fairly good heat output in our car.
That is, until my wife said something about green fluid leaking from the dash near her feet.
We pulled over, and several other drivers also stopped in solidarity. Fortunately, the coolant loss was small enough that the temp gauge stayed in the Normal range. With assistance from several helping hands, we routed the heater hoses in a “U”, bypassing the core. The leak stopped, but we had no heat. Within a few hours, grey skies gave way to sunshine, and a significant jump in the thermometer. By the time we reached Nashville, temps were in the 80s.
This was the first time I had attended a show of this magnitude. Memory tells me that there were about 3,000 Mustangs in attendance. Once we entered the parking lot, it was first-come first-served to find a spot; except for some pre-chosen cars parked under cover, there was no attempt to organize the field. We parked and walked around. The Ford Motor Company was an official sponsor, so it was a treat to see one of the first Ford GTs. Edsel Ford II (son of Henry Ford II) was in attendance, and had a friendly greeting for anyone who came by his way.
This was a 3-day show, and Day 2 was not that different from Day 1. Temperatures stayed in the 80s, and cars were kicking up a lot of dust in the gravel parking lot. The heat and the dust did not make walking an enjoyable endeavor. I did spot a number of other GT/CS cars, and when possible, introduced myself to the owners.
One evening, there was a caravan into downtown Nashville, where we saw a show at the Grand Ole Opry, and enjoyed some local BBQ. By Day 3, we were ready to head home. We drove sans caravan, stopping at a B&B on the way, and taking in the scenic views of the Blue Ridge Parkway and Skyline Drive through Virginia.
We got home without further incident. The Mustang did 2,200 miles, flawless except for the leaky heater core (for which I should have known better). Now I knew what I’d be working on during the upcoming winter!
All photographs copyright © 2017 Richard A. Reina. Photos may not be copied or reproduced without express written permission.